Clik here to view.
Proposed Slope to Meet Subbase Daylight
Hello,In my template I am proposing a 1:4 slope on the outside. Sometimes the slope touches down before the subbase daylight, see image below. Is there a way that in this situation I can force my slope...
View ArticleRoadway Designer Station Interval
I am working in RD and the station interval is using the beginning of my profile as a start station, and running at 5' intervals. I have the station lock on even stations, My corridor begins at an...
View ArticleI lost my profile link to my corridor. How do I get it back?
I lost my corridor "link" to my vertical alignment. I don't know how this could happen. My templates drops are in 3d, but in the cross-section viewer the vertical alignment point is at Zero. Any hope...
View Article"Store Graphics" error for horizontal alignment
I have tried "store graphics" several times to create a horizontal alignment using a complex chain I created. Every time I try to store the chain, geopak/microstation crashes and this message comes up...
View ArticleSuperelevation Inroads ss3 table method?..........sup files
Has this method gone away?I followed the on line tutorials and I get very strange results
View ArticleClik here to view.
Missing Features after exporting DTM to XML and then re-importing
Hello,I’ve exported out our DTM to XML using LandXML Translator. I then Import that XML to verify that it had been properly exported. However, when I compare the XML to the original DTM, the XML is...
View ArticleMoving Horizontal PI in Openroads
How can I move a Horizontal PI on a complex alignment using Openroads? (The equivalent to Geometry-Horizontal Curve Set-Move PI in Inroads).
View ArticlePROFILE
How do I display a feature in a profile that isn't crossing but projected?ThanksMark
View ArticleReverse stationing in Geopak
I'm using V8i ss2, can't seem to reverse my stationing no matter what I try. I changed the "direction" of my alignment using the modify curve tool and that didn't help either. I have a known station...
View ArticleQuick dynamic section
Hi there, I had a couple of years break from using MX. Last time I worked on it it was v.2004 build8.05. In that version if you wanted to take a quick section in any direction not referenced to any...
View ArticleClik here to view.
Free swept path analysis software
In 2010 I posted information about a free Vehicle Simulation Software (MSTurn) for Microstation. Version two of MSTools is now available. This version has some improvements and is developed for .net...
View ArticleImporting lidar data
I am trying to import lidar data sir but invain.I tried many many times ,i am struck at this level. My project is road design using lidar data, is it possible practically because Iam facing a lot more...
View ArticleCorridor Modeler Cross Section Labeler
I cannot open the CM Cross Section Labeler. I don't get an error pop-up. The tool simply does not open.I am running SS3 08.11.09.608 and Geopak 08.11.07.566.I deleted all Geopak .rsc files as...
View ArticleUnits Synchronization Alert
I have been getting this alert recently on files that never used to trigger this. Any ideas as to why my units are not synchronized? When working in a model with a sheet microstation kicks up the...
View ArticleOpenRoads SS4 - Creating skewed, custom, additional cross sections
Having trouble finding anything videos, instruction, etc. on how to create skewed or additional cross sections when there are culverts or entrances that we would like to show in our cross section...
View ArticleClik here to view.
Create Surface Corridor Modelor
Howdy! I am having issues creating a surface out of my model. The end conditions seem to be hitting the correct spot, but after that the created surface is going straight down like it's trying to tie...
View ArticleGeopak Chains regions when using same point
Have series of points defining a T-intersection and when I enter the points to make a chain, it creates a region and an associated equality in the other chain.How can I get rid of the regions and...
View ArticleClik here to view.
Hover over element with no display - InRoads SS3
This screen capture is from a Bentley Learn video. When I am preforming the same operation, all of the text in yellow in Blank. I cannot figure out why. Is this a display problem?InRoads -...
View ArticleCross Section to Surface -- Creates Empty Surface
I have a colleague who recently cut some cross-sections in InRoads SS2 v08.11.07.615. Here is a brief description of the problem:- InRoads recognizes the cross-section set (good)- When using the...
View ArticleCoordinate Geometry - Curve utility is unable to visualize curve
This is something I've repeated done for years and has just recently become a problem.
View Article