[MX V8i SS3] Point codes replacement
Hello,I want to change standard point codes for geometry string in MX to our local codes. In user manual I found only annotation:"The codes PBC etc may be replaced by an alternative National code by...
View ArticleGEOPAK-ALIGNMENT LABEL-USER SPECIFIED LOCATION
Hello,I am new to Geopak V8i SS2.Using the Plan View Labeler, I was unable to label an alignment at a user specified station. So if I wanted to locate a specific station and offset, such as 8+91.23 at...
View ArticleGEOPAK-TEMPLATE-POINT CONTROL TEST
Hello,I am new to Geopak V8i SS2 and learning the Corridor Modeling Create Template tools. If I right click a point in my template and select Test Point Controls->Test Horizontal Point Control; I...
View ArticleGEOPAK CORRIODR-SETTING ACTIVE / DEFAULT SURFACE
Hello,I am new to Geopak V8i SS2 and learning the Corridor Template concepts.I have attached a screen shot of what I believe is the "active" surface. Am I correct that this is where I set the active...
View ArticleGEOPAK CORRIDOR-COMPONENT EDIT
Hello,I am new to Geopak V8i SS2 and learning the Corridor Template concepts.I have built an end condition, corridor template component, and want to change the slope after its been created. If I...
View ArticleImport FWD into Geopak Loses Point Notes
We are trying to use survey data that was originally setup with InRoads and bring it into Geopak. We were given an FWD file of the topo, and when I "Load Data" within Geopak SS3, and select the FWD...
View ArticleGEOPAK-ROADWAY DESIGNER SECTION DIAGONAL
I am new to Geopak V8i SS2 and learning how to use the Corridor and template tools.Attached is an image of my plan, cross section and profile from the Roadway Designer view. The left side of the...
View ArticleTwo Surfaces Label in Profile Inroads SS2
I have two surfaces my existing and rough grading, I want to show in profile the levels of my two surfaces and their corresponding difference in elevation along the corresponding alignment. Can someone...
View ArticleGEOAPK-CORRIDOR SURFACE
I am new to Geopak V8i SS2 and learning corridors.I have created a corridor surface and believe inorder to view surface, I have to triangulate surface first, then Load contours and breaklines to view...
View ArticleEarthwork Error Message - XS-W-Dangprop
Geopak V8i 08.11.07.615 I'm running Geopak Earthwork on cross sections and am constantly getting the "XS-W-DANGPROP Proposed undercut element between points:..."The earthworks ran fine in Geopak v8.I...
View ArticleHorizontal Geometry Tools - Tan/Tan/Tan (Power Inroads 081109674)
Is there a way to create a simple arc via 3 tangents? So selecting a staight, arc, straight to create a horizontal curve. We can create this using microstation tools, followed by tracing with civil...
View ArticleGOEPAK-D &CM WORKFLOW
Hello,I am new to Geopak V8i SS2.I have been learning the Design and Computation Manager. I have selected the Geotechnical Rock Plating item in the left pane, selected Place Influence and Draw COGO...
View ArticleGEOPAK-D&CM ATTRIBUTE ATTACHED TO ELEMENT
Hello,I am new to Geopak V8i SS2.I am learning the Design and Computation Manager functionality.I have drafted a hatch pattern using the steps in the attached image. The boundary was traced from a...
View ArticleClik here to view.
SS3 Cross Section doesn't connect to the ground
Hi, We are using Microstaion 08.11.09.578 Geopak 08.11.09.674.When we open the Cross Section model and Create cross section we see that the end condition of the reference model doesn't touch the...
View ArticleGEOPAK-D&CM SET
Hello,I am new to Geopak V8i SS2.I am learning the D&CM functionality. I understand the Set mode in the D&CM will change the symbology of selected item to that of category selected in left...
View ArticleGEOPAK-DCM FUNCTIONALITY
Hello,I am new to Geopak V8i SS2.I have been trying to learn the Design and Computation Manager functionality. I was hoping I could use the Design and Computation manager to draft linework using the...
View ArticleCorridor Modeling
I am currently looking into more efficient ways of designing utilizing Geopak and Microstation and have come across corridor modeling. Does this (or any Bentley Application) have the ability to update...
View ArticleClik here to view.
Grid Display and axis are broken in PowerInroads V8İ
Hello. I am new to Inroads and Microstation. Grid Display and axis are broken in PowerInroads V8İ on Windows 7 64bit. There is also blue line between axis. I do not exactly know the reason of this...
View ArticleImporting Descriptions of Survey Point Data
I use PowerCivil V8i (Select Series 2). I need to import descriptions with my point data. I am able to import the data sometimes, and other times it will not import. I use ODOT config files and a *.dc...
View Article